HL-DT-ST DVD GDR8162B DRIVER

XP doesn’t have the drivers built in for most things that first came out after XP was first released, circa , and it doesn’t have some of the drivers built in for things made before that. It may NOT be able to recognize some types of “burned” disks that already have data on them. Your drive is an IDE drive. You don’t need to install drivers for it. It is common to un-intentionally damage IDE data cables, especially while removing them – the 80 wire ones are more likely to be damaged. I have discovered I have the same model sitting around. There are two rows of 3 pins on the back of the drive next to the pins for the IDE header.

Uploader: Zutaxe
Date Added: 10 February 2005
File Size: 31.18 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 91212
Price: Free* [*Free Regsitration Required]

There are two rows of 3 pins on the back of the drive next to the pins for the IDE header. There must be a jumper on one of those three pairs of pins.

Make sure that there are no pins on the drive or on the mboard IDE headers that are bent over such that they’re not plugging into the data cable connectors. You don’t need to install drivers for it. The side of the data cable that has a colored stripe must be next to the 4 pin power socket. If you load drivers from the web, brand name system builders and mboard makers gdrr8162b DO NOT have the main chipset drivers listed in the downloads for your model – in that case you must go to the maker of the main chipset’s web site, get the drivers, and load them.

The jumper setting on the back of the drive must be set properly. Thousands of users waiting to help!

  INTEL 82540EM BASED GIGABIT NETWORK ADAPTER PCI DRIVER

HL-DT-ST DVD-ROM GDRB USB Device Drivers Download for Free | Driver Talent

Yes No I don’t have a dog. Over a Month Ago Time Zone: Usually the thing that makes them un-usable first is the cheap sleeve bearings in the motor have worn to the point that so much friction is produced in the bearings that the motor can no longer spin at the minimum 1X legacy audio CD speed, or the motor doesn’t spin at all.

If you have a generic system and have hl-dr-st CD that came with the mboard, all the necessary drivers are on it. Net cannot verify the validity of the statements made on this site. It is common to un-intentionally damage IDE data cables, especially while removing them – the 80 wire ones are more likely to be damaged. It should either show up in the bios Setup, or if you have an old mboard, the model of the drive should show up on the first black screen while booting the computer.

What the pins are for is stamped into the metal on top of the drive. I have discovered I have the same model sitting around. You must have both a power connector from the power supply and a data cable properly connected to tdr8162b drive. That model is relatively old.

The computer’s bios MUST be detecting the drive. It was made in August Net and its accuracy. Another common thing is for the data ggdr8162b to be separated from the connector contacts hl-dt-t bit after you have removed a cable – there should be no gap between the data cable and the connector – if there is press the cable against the connector to eliminate the gap. Would you use Snapchat filters on your dog?

  M1009 BLAZER DAILY DRIVER

Net is the opinions of its users. It may NOT be able to recognize some types of “burned” disks that already have data on them. Solved i need the drivers for Hl-dt-st dvd-rom gdrb instalation.

LG HL-DT-ST dvd-rom GDR8162B Free Driver Download

Your drive is an IDE drive. Default bios settings are usually already set so any drive that is properly connected, and has the proper jumper setting if it’s an IDE drive, will be detected Hl-dt-sr you think bios settings may have been set wrong, load bios defaults, Save bios settings.

If it is possible for a data cable connector to plug into a IDE header either way, the striped side of the data cable must be next to the pin one end of the IDE header on all connections. Use Question Form such as ” Why? Usually the pin one end of the IDE header on the drive is next to the power socket. If that doesn’t help, you may need to change a setting regarding drive detection – e. Your drive does not require an 80 wire data cable – a 40 wire one will do – but if it’s on the same data cable as a hard drive that requires an 80 wire data cable, you must use an 80 wire data cable to get the full max burst speed from the hard drive.

XP has no built in software codec that can read encoded DVDs, such as pre-recorded movies. The information on Computing.